Cheap 3D Printer Guide With Reviews – 2017 Top 3

Looking for a 3D printer for sale in 2017? Find the best offers here.

There was a time when searching for 3d printer reviews was an exercise in futility, but now that’s no longer true. With 3D printers becoming more popular and technology advancing, the cost of these devices have gone down considerably. Resulting in a lot more homes across the US owning and reviewing the best buys. Below are our top 3 picks for fun yet affordable 3D printing.

The three 3D printers here are entry level, but even so they have some excellent features and the output is high quality. Another thing that should be pointed out now is that these printers require assembly: the good news is most of them have detailed instructions or videos that make the process clearer.

Our Top Pick

Reprap Guru Prusa I3 DIY 3D Printer Kit

For more information click the image

For more information click the image

The Reprap Guru is top of our list. It does not need any cutting, drilling and soldering, and with an 8 x 8 x 7 inch build area, it is more than comparable to other more expensive 3D printers. This is also one of those few 3D printers that can run on 220V and 110V so that’s one less thing to worry about.

See more reviews for the Reprap here.

The Reprap also comes with all the required wires as well as the 8″ x 8″ borosilicate heat bed glass solder and the motor wires. The printer is also compatible with Windows, Linux and the Mac so it doesn’t matter what your operating system is. Compatibility is a common problem for 3D printers so it’s good to know that is not the case here.

One of the things you need to look at is the bed and ensure that it is leveled. Before printing anything, make sure the printer is set on an even surface as this will affect the final output. Speaking of the output, it is very good and much better than what you would expect from an affordable printer.

If you have experience building 3D printers before, this should pose no problems. If not, you need to be patient especially with the calibration and build. All the parts you need to construct and use the printer are included here, but pay attention to the end stop brackets: while they need to be tight, don’t overdo as it could snap. All you really need to do is set it tight enough so everything remains in place.

Runner Up

Two Up v2 3D Printer Kit

For more information click the image

For more information click the image

-7″ x 7″ x 5″ i3 Build Dimensions
-50 Micron
-1.75mm PLA ABS Nylon

If you’re looking for a cheap 3d printer, it’s hard to beat the TwoUp as it retails for less than $280. The printer does not require soldering, which is nice, and there are clear instructions on how to assemble the unit.

This is the second version of the TwoUp and it improves a lot on the original especially when it comes to quality. The unit comes with a bolted linear brackets that speed building time, reduces sag and boosts rigidity. The print quality has been improved as well and calibration has been simplified too.

See more reviews for the TwoUp here.

The TwoUp also has a new electronic set up that is more dependable, plus it is capable of dealing with faster speeds, not to mention the fact that installation and setup is easier now. It’s also worth pointing out the instructions have more images so it’s easier to follow, and the Z axis nut is now much more precise, and it’s self-lubricating too so there’s no more squeaking noises here.

The TwoUp has also improved its extrusion thanks to the filament drive gear tooth geometry, and the filament guide centers the filament for faster and more efficient printing.
The build area is 175 x 175 x 125 mm, more than sufficient for entry level 3D printing, plus it comes with a CNC chassis with precision linear motion parts. If you take a close look at the printer you’re going to see that it has ACME machined screws so the motion is consistent and precise. When it comes to the output, you will be hard pressed to find one that is as good as this. While entry level, don’t let that fool you as the output is top notch.

Third Place

[New Arrival] HICTOP Portable Desktop 3D Printer

For more information click the image

For more information click the image


-High Accuracy CNC
-Self-assembly
-Works with PLA, Rubber, Wood

Like other 3D printers, this one requires DIY assembly but thankfully the instructions are clear and easy to follow.

The printing size measures 130 x 150 x 100 mm so it’s more than enough for those new to 3D printing, and the quality is good. The printing speed is 100mm/s, which is right up there with other entry level 3D printers, and there’s support for an SD card and LED screen as well.

See more reviews for the HICTOP 3d Printer here

The printer measures 280 x 300 x 320 mm so it’s compact. Also, the learning curve isn’t that difficult compared to other, more complex 3D printers. It’s also compatible with most 3D graphics programs and all the tools you need to assemble the printer are included.

One other bone of contention for many of those new to 3D printing is the difficulty that comes with the assembly. Fortunately the HICTOP is simpler to put together than other 3D printers, though the wiring and belts can be a bit involved. Another good thing is there are a lot of spare parts included, great for beginners who might encounter trouble trying to get the printer to run. The print quality is good for an entry level printer and simple enough for even older children to use.

Conclusion

So which of the 3d printers for sale above is the best option? It’s really up to you and your personal requirements. Aside from the low cost for a cheap 3d printer, it’s also going to help if you know how 3D printers work as it’s going to make it easier to decide what to buy.

Back to Top


Comments

  1. Martin @ Living on Your Patio
    August 23, 2016 - 5:12 am

    I’m completely new to 3D printers. Is it possible to download designs that I can use to make things with my printer? If there are, where would you recommend? I’m pretty useless when it comes to designing stuff by myself.

  2. Thanks, this is going to make the choice easier – i like The Reprap Guru printer, i can set it up so my friends can see it, and it will make me look like a tech head. I already have a few projects i want to start on. Is there a particular filament you would recommend?

  3. This technology is amazing to me and appears to be much more affordable. Do you have ideas about what’s involved in maintenance, and how much I should expect to spend on materials after getting a 3d printer? Thanks for the reviews!

  4. 3D Printing is completely new to me. I see your amazing examples to the side and am impressed. The thought of assembly scares me off but you make it sound like the process is not difficult. Great info here!

Leave a Reply

Your email address will not be published / Required fields are marked *